About Pump RIGHT
Submersible pump entirely in AISI 304 stainless steel and open vortex impeller, which can be used in fixed and mobile installations. Suitable for domestic applications and large industrial wastewater lifting installations
Features
- Possibility to use in fixed and mobile installations
description Pump RIGHT
Submersible pump entirely in AISI 304 stainless steel and open vortex impeller, which can be used in fixed and mobile installations.
The RIGHT electric pump is also available with a float switch that allows for wide use.
For further technical information see the Databook
- Handling of soiled liquids containing solid and/or filamentary substances in suspension
- Emptying of seepage water
- Handling of dirty wastewater (sanitary)
- Emptying of cesspits and discharge to sewers
Overview of technical data RIGHT
| Flow rate | Up to 18 m³/h |
| Total head | Up to 9.5 m |
| Max. temperature of the liquid | +50°C |
| Poles | 2 |
| Max. solids passage | 35 mm |
| Insulation class | F |
| Protection degree | IPX8 |
| Voltage | Single-phase 1~230V ± 10% Three-phase 3~400V ±10% |
| Max. immersion | 7 m with 10 m cable 2 m with 5 m cable |
Material Pump RIGHT
| Pump body | AISI 304 (EN 1.4301) |
| Impeller | AISI 304 (EN 1.4301) |
| Shaft | Stainless steel AISI 303 (EN 1.4305) (part in contact with liquid) |
| Mechanical seal | upper part in Carbon/Ceramic/NBR (motor side) lower part in Silicon Carbide/NBR (pump side) |
pump RIGHT
PERFORMANCE CURVE SPECIFICATIONS
The specifications below qualify the curves shown on the following pages.
Tolerances according to ISO 9906 Annex A
The curves refer to effective speed of asynchronous motors at 50 Hz
Measurements were carried out with clean water at 20°C of temperature and with a kinematic viscosity
of ν = 1 mm2/s (1 cSt)
In order to avoid the risk of over-heating, the pumps should not be used at a flow rate below 10% of best efficiency point.
Symbols explanation:
Q = volume flow rate
H = total head
Submersible electric pumps for waste water in AISI 304
Submersible electric pump for waste water in AISI 304 stainless steel.
Pump body, impeller, motor cover, seal holder disc and motor case in AISI 304. Shaft in AISI 303 (part in contact with the liquid). Present the double mechanical seal with oil chamber: the upper one in Carbon/Ceramic/NBR (motor side) and the lower one in SiC/SiC/NBR (pump side).
Special Versions
– MA Version with float
– Version with 10 m of cable
INSTALLATION
The RIGHT electric pumps are also available with a float switch, thus increasing the versatility of use. The choice of the use of the float switch requires the respecting of minimum installation spaces to guarantee correct operation of the pump itself.
Technical
- Flow rate Up to 18 m³/h
- Total head Up to 9.5 m
- Max. temperature of the liquid +50°C
- Poles 2
- Max. solids passage 35 mm
| Pump type | KW | Capacitor | Absorbed current | Q=Capacity | |||||||||||
Single-phase 230V 50Hz | Three-phase 400V 50Hz | µ F | Vc | 1~ | 3~ | l/min | 40 | 80 | 100 | 120 | 160 | 200 | 240 | 300 | |
| m/h | 2.4 | 4.8 | 6 | 7.2 | 9.6 | 12 | 14.4 | 18 | |||||||
| H=Total head | |||||||||||||||
| RIGHT 75m | RIGHT 75 | 0.55 | 20 | 450 | 4.8 | 2.1 | 7.8 | 6.8 | 6.2 | 5.7 | 4.7 | 3.4 | 2 | – | |
| RIGHT 100m | RIGHT 100 | 0.75 | 31.5 | 450 | 5.7 | 2.6 | 9.5 | 8.6 | 8.1 | 7.6 | 6.6 | 5.4 | 4.2 | 2 | |
