Description pump 1i-10is-10ix
Line of electric motors from 10” asynchronous, rewindable built in the following execution: – 10I motor sleeve made by AISI 304 and with upper/lower support made by cast iron; – 10IS motor sleeve and upper/lower support made by AISI 304; – 10IX motor sleeve and upper/lower support made by AISI 316. Motor is filled with a water and glycol mixture (freezing point -15°C) guarantees cooling and lubrication of the thrust unit (Kingsbury type self-centering onoscillating pads and graphite spacer ring) and of the bushings; pressure compensation occurs through a rubber membrane located on the lower side and a compensation valve in the upper part, possibility to install the PT100 sensor even subsequently.
Line of 10 ”asynchronous, rewindable electric motors built in the following versions: 10I, 10IS, 10IX. The engine filled up of a mixture of water and glycol ensures cooling and lubrication of the thrust bearing unit and bushings. For applications with inverters or for use with liquids with temperature above 30 ° C insulation in PE2 + PA is available.
Line of electric motors from 10 ”asynchronous, rewindable built in the following execution: 10I, 10IS, 10IX. Motor is filled with a water and glycol mixture guarantees cooling and lubrication of the thrust unit. For applications with inverter or with liquid with temperature higher than 30 ° C insulation type PE2 + PA is available.
MODEL 3~ | HP | kW |
---|---|---|
10I 125 | 125 | 92 |
10I 150 | 150 | 110 |
10I 180 | 180 | 132 |
10I 200 | 200 | 147 |
10I 250 | 250 | 185 |
10I 125 I | 125 | 92 |
10I 150 I | 150 | 110 |
10I 180 I | 180 | 132 |
10I 200 I | 200 | 147 |
10I 250 I | 250 | 185 |
10I 125 PPA | 125 | 92 |
10I 150 PPA | 150 | 110 |
10I 180 PPA | 180 | 132 |
10I 200 PPA | 200 | 147 |
10I 250 PPA | 250 | 185 |
10I 125 VP | 125 | 92 |
10I 150 VP | 150 | 110 |
10I 180 VP | 180 | 132 |
10I 200 VP | 200 | 147 |
10I 250 VP | 250 | 185 |
MODEL 3~ | HP | kW |
---|---|---|
10I 125 | 125 | 92 |
10I 150 | 150 | 110 |
10I 180 | 180 | 132 |
10I 200 | 200 | 147 |
10I 250 | 250 | 185 |
10I 125 I | 125 | 92 |
10I 150 I | 150 | 110 |
10I 180 I | 180 | 132 |
10I 200 I | 200 | 147 |
10I 250 I | 250 | 185 |
10I 125 PPA | 125 | 92 |
10I 150 PPA | 150 | 110 |
10I 180 PPA | 180 | 132 |
10I 200 PPA | 200 | 147 |
10I 250 PPA | 250 | 185 |
10I 125 VP | 125 | 92 |
10I 150 VP | 150 | 110 |
10I 180 VP | 180 | 132 |
10I 200 VP | 200 | 147 |
10I 250 VP | 250 | 185 |
Upper / bottom support | cast iron (10I); AISI 304 (10IS); AISI 316 (10IX) |
---|---|
External jacket | AISI 304 / AISI 316 |
Mechanical seal | ceramic-graphite; SiC optional |
Ball bearings | radial and axial, water lubricated |
Number of startups/hr | max 5 |
Asynchronous 2 poles rewindable in oil bath | 3~ 3x400V ± 10% – 50 Hz, 3~ 3×400/690V ± 10% – 50 Hz |
---|---|
Cooling Flow | min 1 m/s |
Insulation class | B |
Insulation | Double Insulation (I); PE2 + PA (PPA); VPE (VP) |
Protection degree | IP68 |